EMT Practice Test

1. Question Content...

---

Question1: What are two types of supported IPSec VPNs in NSX-T Data Center? (Choose two.)

Question2: Which NSX CLI command is used to check the GENEVE tunnel status on ESXi transport node?

Question3: Which CLI command should be executed on a KVM hypervisor to retrieve the VM interface UUID?

Question4: Which two commands does an NSX administrator use to check the IP address of the VMkernel port for the GENEVE protocol on the ESXi transport node? (Choose two.)

Question5: An NSX administrator noticed that the nsxcli command times out after 600 secs of idle time.
Which CLI command disables the nsxcli time out value on NSX Manager?

Question6: Which profile must be attached to the ESXi cluster to prepare the host for NSX-T Data Center?

Question7: What are two valid options when configuring the scope of a distributed firewall rule? (Choose two.)

Question8: An NSX administrator has deployed an NSX Edge on a bare-metal server.
Which command registers the NSX Edge with the NSX Manager?

Question9: A user is assigned these two roles in NSX Manager:
LB Admin
Network Engineer
What privileges does this user have in the system?

Question10: An NSX administrator has deployed an NSX Edge on a bare-metal server.
Which command registers the NSX Edge with the NSX Manager?

Question11: Which CLI command is used to start the NSX Manager virtual machine in the KVM environment?

Question12: Which command is used to set the NSX Manager's logging-level to debug mode for troubleshooting?

Question13: An NSX administrator is creating a NAT rule on a Tier-0 Gateway configured in active-standby high availability mode.
Which two NAT rule types are supported for this configuration? (Choose two.)

Question14: Which CLI command shows syslog on NSX Manager?

Question15: Which CLI command is used to start the NSX Manager virtual machine in the KVM environment?

Question16: Which to steps must an NSX administrator take to integrate VMware Identity Manager in NSX-T to support role-based access control? (Choose two.)

Question17: Which command is used to set the NSX Manager's logging-level to debug mode for troubleshooting?

Question18: Which CLI command does an NSX administrator run on the NSX Manager to generate support bundle logs if the NSX UI is inaccessible?

Question19: Where are Distributed Firewall logs containing access decisions stored?

Question20: Which network virtualization technologies can be used with an Ethernet VPN (EVPN) deployment in NSX-T Data Center? (Choose two.)

Question21: Which step must be performed before deploying an additional NSX Manager from the NSX-T UI?

Question22: Which log is used to see a failed NSX-T installation of a VIB package on ESXi transport nodes?

Question23: An NSX administrator has observed connectivity issues between the NSX Manager and the KVM Transport Node.
Which two log files could be used to troubleshoot the issue on the KVM Transport Node? (Choose two.)

Question24: Which CLI command should be executed on a KVM hypervisor to retrieve the VM interface UUID?

Question25: Which CLI command does an NSX administrator run on the NSX Manager to generate support bundle logs if the NSX UI is inaccessible?

Question26: How does Traceflow tool identify issues in a network?

Question27: Which two BGP configuration parameters can be configured in the VRF Lite gateways? (Choose two.)

Question28: What are two supported N-VDS modes? (Choose two.)

Question29: Which two statements are true for a Tier-1 Gateway? (Choose two.)

Question30: Where are Distributed Firewall logs containing access decisions stored?

Question31: Which CLI command shows syslog on NSX Manager?

Question32: Refer to the exhibit.

Which NAT type must the NSX-T Data Center administrator create on the Tier-0 or Tier-1 Gateway to allow Web VM to initiate communication with public networks?

Question33: An NSX administrator is using ping to check connectivity between VM1 running on ESXi1 to VM2 running on ESXi2. The ping tests fails. The administrator knows the maximum transmission unit size on the physical switch is 1600.
Which command does the administrator use to check the VMware kernel ports for tunnel end point communication?

Question34: How many IPs are required when deploying a highly available NSX Management Cluster with VIP in a production environment?

Question35: When deploying east-west network introspection, which Service Virtual Machine (SVM) deployment method achieves the least amount of traffic hairpinning?

Question36: An NSX administrator wants to create a Tier-0 Gateway to support equal cost multi-path (ECMP) routing.
Which failover detection protocol must be used to meet this requirement?

Question37: Which three steps are required to create an IPsec VPN tunnel? (Choose three.)

Question38: When deploying east-west network introspection, which Service Virtual Machine (SVM) deployment method achieves the least amount of traffic hair pinning?

Question39: When deploying east-west network introspection, which Service Virtual Machine (SVM) deployment method achieves the least amount of traffic hairpinning?

Question40: An NSX Administrator has created a segment named WEB-LS from the NSX UI and noticed the segment is not realized on the KVM Transport node.
What are two possible causes for this issue? (Choose two.)

Question41: How is the RouterLink port created between a Tier-1 Gateway and Tier-0 Gateway?

Question42: What needs to be configured on a Tier-0 Gateway to make NSX Edge Services available to a VM on a VLAN- backed logical switch?

Question43: Which CLI command shows syslog on NSX Manager?

Question44: An NSX administrator noticed that the nsxcli command times out after 600 secs of idle time.
Which CLI command disables the nsxcli time out value on NSX Manager?

Question45: Which two choices are use cases for Distributed Intrusion Detection? (Choose two.)

Question46: Which two commands are used to query the arp-table of a logical switch? (Choose two.)

Question47: When running nsxcli on an ESXi host, which command will show the Replication mode?

Question48: Which two statements are true about the implementation of multicast in NSX-T Data Center? (Choose two.)

Question49: Which Network and Security virtualization solution provides network hybridity and mobility?

Question50: An NSX administrator has configured a KVM hypervisor as a transport node.
Which kernel module on KVM implements a N-VDS?

Question51: When a stateful service is enabled for the first time on a Tier-0 Gateway, what happens on the NSX Edge node?

Question52: Which is correct when deploying a NSX Edge in a KVM only environment?

Question53: An NSX administrator is reviewing syslog and notices that Distributed Firewall Rules hit counts are not being logged. What could cause this issue?

Question54: The NSX Control Plane is responsible for which two functions? (Choose two.)

Question55: An NSX administrator is troubleshooting a connectivity issue with virtual machines running on an ESXi transport node. Which feature in the NSX UI shows the mapping between the virtual NIC and the host's physical adapter?

Question56: Which two statements are true about the implementation of multicast in NSX-T Data Center? (Choose two.)

Question57: A security administrator needs to configure a firewall rule based on the domain name of a specific application. Which field in a distributed firewall rule does the administrator configure?

Question58: Which two statements are true about the implementation of multicast in NSX-T Data Center? (Choose two.)

Question59: Which statement Is true regarding the audit user account? (Choose two.)